Required Permissions

StackState Self-hosted v4.6.x

This page describes StackState version 4.6.

Go to the documentation for the latest StackState release.

Overview

All of StackState's own components can run without any extra permissions. However in order to install StackState successfully, you need some additional privileges, or ensure that the requirements described in this page are met.

Autonomous Anomaly Detector (AAD)

In order to run the Autonomous Anomaly Detector, or prepare your Kubernetes cluster to run it, StackState needs to create a ClusterRole and two ClusterRoleBinding resources. Creating these cluster-wide resources is often prohibited for users that are not a Kubernetes administrator.

Disable automatic creation of cluster-wide resources

The automatic creation of cluster-wide resources during installation of StackState can be disabled by adding the following section to the values.yaml file used to install StackState:

cluster-role:
  enabled: false

Note that if automatic creation of cluster-wide resources is disabled the Autonomous Anomaly Detector will NOT be able to authenticate against the running StackState installation unless you manually create the cluster-wide resources.

Manually create cluster-wide resources

If you need to manually create the cluster-wide resources, ask your Kubernetes administrator to create the 3 resources below in the Kubernetes cluster.

Ensure that you specify the correct namespace for the bound ServiceAccount for both of the ClusterRoleBinding resources.

apiVersion: rbac.authorization.k8s.io/v1
kind: ClusterRole
metadata:
  name: stackstate-authorization
rules:
- apiGroups:
  - rbac.authorization.k8s.io
  resources:
  - rolebindings
  verbs:
  - list
apiVersion: rbac.authorization.k8s.io/v1
kind: ClusterRoleBinding
metadata:
  name: stackstate-authentication
roleRef:
  apiGroup: rbac.authorization.k8s.io
  kind: ClusterRole
  name: system:auth-delegator
subjects:
- kind: ServiceAccount
  name: stackstate-api
  namespace: stackstate
apiVersion: rbac.authorization.k8s.io/v1
kind: ClusterRoleBinding
metadata:
  name: stackstate-authorization
roleRef:
  apiGroup: rbac.authorization.k8s.io
  kind: ClusterRole
  name: stackstate-authorization
subjects:
- kind: ServiceAccount
  name: stackstate-api
  namespace: stackstate

Elasticsearch

StackState uses Elasticsearch to store its indices. There are some additional requirements for the nodes that Elasticsearch runs on.

As the vm.max_map_count Linux system setting is usually lower than required for Elasticsearch to start, an init container is used that runs in privileged mode and as the root user. The init container is enabled by default to allow the vm.max_map_count system setting to be changed.

Disable the privileged Elasticsearch init container

In case you and/or your Kubernetes administrators do not want the privileged Elasticsearch init container to be enabled by default, you can disable this behavior in the file values.yaml used to install StackState:

elasticsearch:
  sysctlInitContainer:
    enabled: false

If this is disabled, you will need to ensure that the vm.max_map_count setting is changed from its common default value of 65530 to 262144. If this is not done, Elasticsearch will fail to start up and its pods will be in a restart loop.

To inspect the current vm.max_map_count setting, run the following command. Note that it runs a privileged pod:

kubectl run -i --tty sysctl-check-max-map-count --privileged=true  --image=busybox --restart=Never --rm=true -- sysctl vm.max_map_count

If the current vm.max_map_count setting is not at least 262144, it will need to be increased in a different way or Elasticsearch will fail to start up and its pods will be in a restart loop. The logs will contain an error message like this:

bootstrap checks failed
max virtual memory areas vm.max_map_count [65530] is too low, increase to at least [262144]

Increase Linux system settings for Elasticsearch

Depending on what your Kubernetes administrators prefer, the vm.max_map_count can be set to a higher default on all nodes by either changing the default node configuration (for example via init scripts) or by having a DaemonSet do this right after node startup. The former is very dependent on your Kubernetes cluster setup, so there are no general solutions there.

Below is an example that can be used as a starting point for a DaemonSet to change the vm.max_map_count setting:

apiVersion: apps/v1
kind: DaemonSet
metadata:
  name: set-vm-max-map-count
  labels:
    k8s-app: set-vm-max-map-count
spec:
  selector:
    matchLabels:
      name: set-vm-max-map-count
  template:
    metadata:
      labels:
        name: set-vm-max-map-count
    spec:
      # Make sure the setting always gets changed as soon as possible:
      tolerations:
      - effect: NoSchedule
        operator: Exists
      - effect: NoExecute
        key: node.kubernetes.io/not-ready
        operator: Exists
      # Optional node selector (assumes nodes for Elasticsearch are labeled `elastichsearch:yes`
      # nodeSelector:
      #  elasticsearch: yes
      initContainers:
        - name: set-vm-max-map-count
          image: busybox
          securityContext:
            runAsUser: 0
            privileged: true
          command: ["sysctl", "-w", "vm.max_map_count=262144"]
          resources:
            limits:
              cpu: 100m
              memory: 100Mi
            requests:
              cpu: 100m
              memory: 100Mi
      # A pause container is needed to prevent a restart loop of the pods in the daemonset
      # See also this Kubernetes issue https://github.com/kubernetes/kubernetes/issues/36601
      containers:
        - name: pause
          image: google/pause
          resources:
            limits:
              cpu: 50m
              memory: 50Mi
            requests:
              cpu: 50m
              memory: 50Mi

To limit the number of nodes that this is applied to, nodes can be labeled. NodeSelectors on both this DaemonSet, as shown in the example, and the Elasticsearch deployment can then be set to run only on nodes with the specific label. For Elasticsearch, the node selector can be specified via the values:

elasticsearch:
  nodeSelector:
    elasticsearch: yes
  sysctlInitContainer:
    enabled: false

See also

Last updated